Just How to Install a Bath Tub Yourself: Removing as well as Replacing.
Just How to Install a Bath Tub Yourself: Removing as well as Replacing.
Blog Article
Just how do you actually feel with regards to How to Install a Bathtub Yourself?
Installing a bath tub isn't precisely brain surgery, but it does call for solid plumbing, carpentry, as well as sometimes, tiling skills. Replacing an old tub with a new one is also a moderately difficult task. If the old tub is conveniently easily accessible, the job can move quickly; if you need to open a wall surface to eliminate the old bathtub as well as place the brand-new bathtub, the task is much harder. In either case, the task is within a residence handyman's skills, although you will require a helper to leave the old tub and set in the brand-new one. Make sure you have actually certified on your own for the task as well as are comfortable attempting it. Rather than working with a professional to take control of a halfway-completed job, it is far better to think about utilizing one before you start. Chances are you may need a specialist plumber to make tube links.
This article will certainly assist you mount a new tub in your shower room if you have already bought a new tub as well as don't need to change the arrangement of your previous water supply pipes.
Your tools as well as product checklist ought to consist of the following:
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your setup, then the first thing you need to do is disconnect the supply of water. After doing so, turn on the taps to drain pipes any kind of water remaining in the system. The process of removing the existing faucets can be quite problematic due to the limited access that is frequently the situation.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the taps. Have a cloth prepared for the staying water that will come from the pipes. As soon as the supply pipelines have actually been gotten rid of, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single faucets from turning throughout this procedure. As soon as the faucets have been removed, the holes in the bath/basin will certainly need to be cleansed of any old sealing substance.
Before going on to fit the brand-new faucets, contrast the pipe connections on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the new faucets to fit.
Suitable New Touches
If the tails of the brand-new taps are plastic, after that you will need a plastic adapter to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet and the other end provides a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will certainly call for minimizing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, place the tap in the placing opening in the bath/basin making sure that the washers remain in place in between the faucet and the sink. Secure the faucet in position with the supplier offered backnut. When the tap is securely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical faucet connectors. The former kind ought to be linked to the tap ends first, tightening just by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Installing the Bath tub
Utilizing the two wood boards under its feet, put the bath tub in the called for placement. The wood boards are practical in evenly spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto four small points.
The following goal is to make sure that the bath tub is leveled all round. This can be attained by examining the spirit level and also readjusting the feet on the bathtub till the level reads level.
To install faucets, fit the bottom of the furthest flexible faucet adapter to the suitable supply pipeline by making a compression sign up with; then do the same for the various other tap.
Switch on the water system and inspect all joints as well as brand-new pipework for leaks and also tighten them if required. Fill the tub and also check the overflow outlet and the normal outlet for leakages.
Ultimately, repair the bath paneling as defined in the manufacturer's instruction manual. Tiling and also securing around the bath tub ought to wait up until the bathtub has been made use of at the very least once as this will settle it right into its last position.
Preparing for the Installation
First of all, the sustaining frame provided with the bath needs to be fitted (if needed) according to the supplier's instructions. Next off, fit the faucets or mixer to the bath tub. When suitable the tap block, it is important to make certain that if the faucet features a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps system to stop pressure on the bath tub.
Fit the adaptable faucet connectors to the bottom of both taps using 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Ensure you utilize all of the supplied washers.
Attach the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom must now prepare to be suited its last position.
Tiling Around the Bathtub
In the location where the bath fulfills the tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the installation can move sufficient to break a stiff seal, creating the water to penetrate the wall surface in between the bath and the tiling, leading to issues with dampness and also possible leaks to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes and also cartridges, and also are capable of securing gaps approximately a size of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with twists of soaked paper or soft rope. Bear in mind to always load the bathtub with water before sealing, to permit the movement experienced when the bathtub is in use. The sealer can fracture fairly early if you do not take into account this movement before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also conveniently offered on the market. It is advisable to fit the ceramic tiles utilizing water-resistant or water-proof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
Do you enjoy reading about Tools You Need to Install a New Bathtub ? Place feedback below. We would be interested to know your reactions about this write-up. Hoping that you come back again before long. Make sure you set aside a second to share this blog if you appreciated it. Thanks for taking the time to read it.
Information Here Report this page